Capacitor Bank Size Calculator
Capacitance per phase and line current for a delta-connected bank of a given kVAR. With the formula, a worked example and typical values.
Try your own numbers
Estimate only. Not engineering or safety advice. Check the result against the applicable standard and the equipment data, and have a competent engineer review it before it is relied on. Terms of use.
Open in the calculator with these values
About this calculator
This page calculates capacitance per phase and bank line current from bank rating, line voltage and frequency. Change any value or its unit and the result updates. The steps below show the working for the default values, so you can check each line against your own method.
Limits of this calculator
Choose capacitors rated above system voltage, and check for harmonics before fitting detuning reactors.
Cross-check: 8 reference cases, calculated from textbook formulas coded separately from the engine by the same author, agree with this calculator. This is not an independent review.
Verification status: Engineering reference
Engineering reference. Formula and method documented and tested against separately coded reference calculations. Not yet Verified: the evidence listed on this page is still needed.
What this calculator checks
- The arithmetic of the published formula for the values you entered, in the units shown.
What remains unverified
- That the inputs suit your application. Take ratings, resistances and constants from the manufacturer data sheet or project specification.
Verification register entry
| Calculation author | Rahul Sharma (author) |
|---|---|
| Technical review | No independent technical review has been carried out |
| Individual professional approval | Not recorded |
| Formula reference | not recorded |
| Standard and edition | Not applicable: Textbook power and energy identity (single-phase, three-phase, power factor, per-unit); no governing standard |
| Standard review state | Not applicable |
| Scope-screening note | not recorded |
| Cross-check test cases | 8 reference vectors (tests/reference_vectors.json) |
| Review date | not recorded |
| Next review date | not recorded |
| Status | Engineering reference |
Needed before this calculator can be marked Verified: reviewer name, qualification and review date; exact formula reference; formula source (textbook or standard); next review date.
Formula
Worked example
| Input | Value |
|---|---|
| Bank rating | 58.4 kVAR |
| Line voltage (L-L) | 415 V |
| Frequency | 50 Hz |
- C = 58.4 kVAR / (3 × 2π × 50 × 415²) = 359.79 µF
- I = 58.4 kVAR / (√3 × 415) = 81.25 A
Assumptions
- Delta connection
- Rated kVAR is at the stated voltage
Choose capacitors rated above system voltage, and check for harmonics before fitting detuning reactors.
Inputs and results
| Input | Unit | Allowed or shown | Note |
|---|---|---|---|
| Bank rating | kVAR | greater than 0 kVAR | |
| Line voltage (L-L) | V | greater than 0 V | |
| Frequency | Hz | greater than 0 Hz |
| Result | Unit | Allowed or shown | Note |
|---|---|---|---|
| Capacitance per phase | µF | Shown to 1 decimal place | |
| Bank line current | A | Shown to 1 decimal place |
How it is calculated
Each input is converted to the base unit of its quantity, the formula above is applied in the order shown in the worked example, and each result is shown in the unit you choose. Results are held at full precision and rounded only for display, except where a step selects a standard size, as the worked example shows. A value outside its allowed range is refused with a message instead of giving a result.
How the result changes with bank rating
| Bank rating (kVAR) | Capacitance per phase (µF) | Bank line current (A) |
|---|---|---|
| 5.84 | 36 | 8.1 |
| 14.6 | 89.9 | 20.3 |
| 29.2 | 179.9 | 40.6 |
| 58.4 | 359.8 | 81.2 |
| 117 | 720.8 | 162.8 |
| 234 | 1,441.6 | 325.5 |
| 584 | 3,597.9 | 812.5 |
Other inputs are the same as in the worked example above.
Standards and further reading
- IEEE Std 1459 (definitions for power quantities under sinusoidal and non-sinusoidal conditions)
Real, apparent and reactive power follow the usual textbook definitions. Tariff and billing rules come from your utility, not from a standard. These are named as background reading. Elecmetric does not embed clause text or rating tables, and the reviewer record for this calculator is separate from this list.
Frequently asked questions
What do I need to enter?
Enter bank rating, line voltage (L-L) and frequency. Change the unit of a value with its selector and the result stays the same.
What does this calculator assume?
Delta connection. Rated kVAR is at the stated voltage.
Which calculators should I use next?
Common next steps are Power Factor Correction and Current THD. The related links at the bottom of this page open them.
How accurate are the results?
Every figure comes from the same tested engine as the Elecmetric calculators and is meant for estimating. 8 reference cases, calculated from textbook formulas coded separately from the engine by the same author, agree with this calculator. This is not an independent review. Check design values against the standard and the equipment data you work to.
Formula guides and reference
Longer explanations with worked examples and tables, written for the same topic.
- Power Factor and the Power Triangle: Power factor formulas: kW, kVA and kVAR from the power triangle, capacitor kVAR to raise power factor
- Power Factor Correction Payback Formulas: Power factor correction payback formulas: the capacitor kVAR, the fall in kVA demand
- Capacitor Formulas: Energy and RC Time Constant: Capacitor formulas for charge, stored energy, series and parallel capacitance and the RC time constant
More Power and Energy calculatorsAll engineering calculatorsCapacitor Bank Size (µF) in Elecmetric